Is your screen showing some unusual spots all of a sudden? Are you worried that you will need to replace the whole device just because of some marks appearing on the LCD display? No need to panic because this problem is easily solvable.
In this guide, we will tell you all about repairing LCD pressure marks and get the detail answer of How to fix Pressure Spots on LCD Screen? We will also learn about the following topics:
- Common problems with LCD displays
- Reasons for pressure spots to appear
- Ways to use an LCD screen in the best way
- How to assess the damage on LCD screen?
Have you ever wondered that the screen is actually the most important component of your televisions, computers and smart phones? After all, what will you do if there is no display? The modern LCDs and LEDs have become really advanced in their resolution and speed however, there may arise some problems from time to time. The pressure marks are a key issue faced by a lot of people therefore, we have brought this article regarding how to fix pressure spots on LCD screen.
How to fix Pressure Spots on LCD Screen
See below guide step by step.
What are the Common Problems with LCD display?
You may have observed the sudden flashing or flickering of your LCD screen usually after it is turned on. The main reason behind it is the loose video cable. In most cases, it is loose from the connection of monitor so if you tighten it there, the display will become stable. The cable can be faulty so you would need to get a new one in that case. Another reason behind the flickering is incorrect refresh rate settings. Most monitors work with 60 Hz refresh rate. The newer models that are specially designed for gaming purposes have higher refresh rates as well. Therefore, you need to see the recommended refresh rate of your display and set it accordingly from the settings.
- Vertical Lines
Users have reported vertical lines on their screens which can be of any colour. The most common issue is with the LCD display. You can find this by applying some pressure on the affected area and see if the lines change in any way. If so, your LCD is damaged and it would need replacement. Therefore, the problem lies with the hardware. However, you may check the display settings from the control panel to check if everything is set at the recommended level. Always keep your display drivers updated and check that the graphics card is working properly as well.
- Dead pixels
This issue is also faced by a lot of people in which a black dot or how to fix black spot on lcd screen starts appearing on the screen permanently. It occurs because the pixel behind that part of the screen does not illuminate. Users often ask, what is the best way to fix a stuck pixel on an LCD screen? Although it does not affect your monitor or overall working in any way, there are still some softwares which can help in fixing dead or stuck pixels. The programs force the area of the affected pixel to change colours rapidly which can solve the problem. You may need to repeat this process for few hours before any change is visible.
Some users have also reported that by applying pressure on the stuck pixel, it started to work again after repeated attempts. However, there is a risk in this procedure because you may damage the screen unknowingly which will put a large bill in your pocket. The best way to deal with dead pixels is to wait and keep using the device unless it does not spread more to the screen.
- Cracks and Spots
If you see a crack or blotch on screen which is significantly different than other colours on the display, it means that the LCD has gone through some physical damage. It can result due to the monitor falling off, liquid splashes on screen, sharp item hitting the screen or any similar event. Unfortunately, this means that you would need to replace the display because it is not possible to repair such damages. The internal components of the screen get damaged which are mostly not repairable.
- Buzzing Sounds
Have you heard a slight buzz while you are working on your computer? It is most probably caused by a problem in the backlights of the display. The older monitors used fluorescent lighting tubes which are known to malfunction easily. The LED monitors have become much better in their efficiency and reliability but the power fluctuations can cause sounds in them as well. Try to keep a voltage regulator with the computer if there are frequent disruptions in power.
- Incorrect Resolution
Have you experienced a change in screen’s resolution or brightness? The major reason behind it is the graphics card. There may be issue in the graphics driver which can be resolved by a software update or re installation. If the problem is still there, then you would need to get a new graphics card for your device. Sometimes, you may need to change the port if other components are working fine. Your battery may have some issue in charging because the displays often adjust themselves while charging and discharging. In such a case, you would need to replace the battery or charger.
- Frequent Shutoffs
This is another common issue faced by a lot of users. The display shut offs randomly. Experts believe that power fluctuations may be a major reason behind this. You need to check the main power supply of your house and see that the circuit breaker does not trip frequently. If so, the issue is with the main electricity. Another cause of the screen shutting down is the overheating of the device. The processor may overheat due to faulty fan or other reasons which you would need to sort out. You can check this easily by touching the laptop or PC’s casing after it turns off. If it feels very hot, the internal components are overheating and the display shuts off automatically to prevent it from further damage.
What causes white spots or dots on TV Screen?
Televisions are a mandatory item at home. People like to spend their free time watching TV and relaxing with their favourite shows or movies. However, the white spots on TV screen can be gruesome to watch and cause users to miss some part of content appearing on screen. The easy solution is to replace your TV or screen with a new one but this is expensive and majority of the users would not wish to do that. Therefore, we will teach you some steps that you can follow and repair your display yourself.
- Take off the TV from the wall mount and put it face down on a firm table or shelf.
- Remove the back panel by unscrewing all the screws one by one. Keep them in a handy place so that you can access them later on.
- Remove the speaker connections by taking out the wires from both sides.
- Remove the screws that hold the source Printed Circuit Boards (PCBs) at the bottom of the device. Also disconnect the cables going towards the upper PCB.
- Take off the screws from the outer bracket of the LCD. It will then remove the casing that borders the display.
- Use vacuum cups to pull out the display panel from the internal casing. Do this step very carefully with the help of another person because the panel is very delicate. Place it on a secure place.
- Unclip the mounts holding the bracket which keeps the internal casing in place.
- You will see a white panel in front of you. There will be some diffuser sheets which are used to distribute the light evenly in LCDs and LEDs. Remove these sheets carefully and keep them on a clean space.
- Now comes the main part. You will see the small, round reflectors that are put over the LED backlights. You need to collect them and put them in their specific places by securing them with locks. Use a small amount of glue if needed.
- Do the whole process in reverse order to assemble the LCD display again. Follow all the steps one by one and give enough time for the whole process.
We hope that you know the answer to how do I fix cloudy spots on LCD TV with the above steps. Keep in mind that this is a long process and it requires a certain amount of technical knowledge beforehand. If you are doing it for the first time, make sure to keep someone else with you who know about LCD displays. Better to get it fixed by a professional if you are still unsure about the process.
Removing Palm Pressure Mark from LCD
Have you ever seen a slight change in the display from a particular area which is only noticeable once you look for it? I experienced a similar issue when I bought my Samsung LCD TV. Although the marks were barely visible, I still wanted to get rid of them because I did not like it when I was watching content on screen. After some research, I got to know about some essential details regarding it.
The marks are mostly caused during the packing/unpacking process of the TVs. In order to prevent them, people should always hold the screens from top to bottom in which they wrap their hands around the panel. Keep your fingers to the back side and do not let much pressure on the display itself. Use suction cups on the areas where the marks are present. This will remove them in majority of cases but if it they still remain, then you would have to replace the screen. Mostly, such pressure marks are negligible so you may keep using the device as it is.
Frequently Asked Questions
- What causes white spots or dots on TV Screen?
The white spots are caused by faulty reflectors inside the LCD panel. Usually, they get removed from their places which leave the gap in the array. This causes the uneven white spots on the LCD. The dots can result due to stuck pixels on the screen. A dead pixel is usually black in colour whereas stuck pixels can be white or any other colour.
- Can you damage an LCD screen by touching it?
No, a light touch does not damage the LCD screen. However, the LCD screens are delicate devices and you must not apply force on them such as pressure, rubbing or scrubbing the display. If you wish to clean it, use a light cloth and place it gently on the screen to wipe off the dust.
- What is the best way to fix a stuck pixel on an LCD screen?
There is no best way to deal with stuck pixels. Often, they result due to internally damaged LCD screens so they are not easily fixable. You can use softwares to force rapid colour transitions on the affected area which may solve the problem. The better way is to wait because some stuck pixels diminish with time as well.
- How do I fix cloudy spots on my LCD TV?
First, display a dark image on the LCD screen which allows you to see the white cloudy spots easily. You can use a cloth and apply pressure on the affected areas gently. In most cases, it solves the problem after you do the process repeatedly for a few days. If the cloudy spots remain, then you would need to replace the screen for a new one.
Now that you know what causes the white spots or dots on TV screen, you are in a better position to judge the damages and ways to repair them. Nobody wants to be in this situation but one must not panic if the LCD screen shows some problems. Nowadays, Internet has made us masters of all fields because of the guides and tutorials available. Repairing LCD pressure marks is no more a thing to be afraid of. However, always make sure that you have done the proper research before opening up the display. The LCD screens are delicate devices and you would not want to damage them further while trying to reduce the previous issues!